. Après, échange thermique, l'interface utilisateur VUINTER du code Abaqus/Explicit a été utilisée pour implanter la loi proposée, afin d'appréhender complètement le contact d'un point de vue mécanique et thermique. Il est désormais possible d'implanter via cette interface-utilisateur n'importe quelle autre loi d'échange thermomécanique (frottement, coefficient de partage de la chaleur, etc.) pour une meilleure estimation des champs thermiques (température, p.et mécaniques

. Enfin, les principales contributions de ce travail de thèse peuvent se résumer ainsi : ? Développement d'une mise en donnée fiable sous Abaqus/Explicit pour la simulation de l'usinage en configuration de coupe orthogonale, et la prédiction de tous les champs thermomécaniques mis en jeu pour le couple outil-matière WC-Co, pp.2024-351

H. Abdel-aal and A. , Division of frictional heat: The dependence on sliding parameters, International Communications in Heat and Mass Transfer, vol.26, issue.2, pp.279-288, 1999.
DOI : 10.1016/S0735-1933(99)00014-7

L. Adam, Modélisation du comportement thermo-élasto-viscoplastique des matériaux soumis à grandes déformations, application au formage superplastique, Thèse de doctorat de l'Université de Liège Faculté des Sciences Appliquées, 2003.

P. Albrecht, New Developments in the Theory of the Metal-Cutting Process: Part I. The Ploughing Process in Metal Cutting, Journal of Engineering for Industry, vol.82, issue.4, pp.348-358, 1960.
DOI : 10.1115/1.3664242

S. Atlati, B. Haddag, M. Nouari, and M. Zenasni, Analysis of a new Segmentation Intensity Ratio ???SIR??? to characterize the chip segmentation process in machining ductile metals, International Journal of Machine Tools and Manufacture, vol.51, issue.9, pp.687-700, 2011.
DOI : 10.1016/j.ijmachtools.2011.05.007

P. J. Arr08-]-arrazola, D. Ugarte, and X. Dom?nguez, A new approach for the friction identification during machining through the use of finite element modeling, International Journal of Machine Tools and Manufacture, vol.48, issue.2, pp.173-183, 2008.
DOI : 10.1016/j.ijmachtools.2007.08.022

P. J. Arr10-]-arrazola and O. ??-?-tugrul, Investigations on the effects of friction modeling in finite element simulation of machining, International Journal of Mechanical Sciences, vol.52, issue.1, pp.31-42, 2010.
DOI : 10.1016/j.ijmecsci.2009.10.001

J. Aur06-]-aurich, C. Bil, and H. , 3D Finite Element Modelling of Segmented Chip Formation, CIRP Annals, vol.55, issue.1, pp.47-50, 2006.
DOI : 10.1016/S0007-8506(07)60363-1

S. Bahi, Modélisation hybride du frottement local à l'interface outil? copeau en usinage des alliages métalliques, 2010.

M. Bäker, J. Rösler, and C. Siemers, A finite element model of high speed metal cutting with adiabatic shearing, Computers & Structures, vol.80, issue.5-6, pp.495-513, 2002.
DOI : 10.1016/S0045-7949(02)00023-8

C. Barlier, C. Lescalier, and A. Mosian, Continuous flank wear measurement of turning tools by integrated micro-thermocouple, Annals of the CIRP, vol.46, issue.1, 1997.

J. Barry and G. Byrne, The Mechanisms of Chip Formation in Machining Hardened Steels, Journal of Manufacturing Science and Engineering, vol.22, issue.3, pp.528-535, 2002.
DOI : 10.1016/0020-7403(80)90070-3

. Bar05, M. Barge, H. Hamdi, J. Rech, and J. Bergheau, Numerical modelling of orthogonal cutting: influence of numerical parameters, Journal of Materials Processing Technology, pp.164-165, 2005.

J. L. Battaglia, L. Lay, . Le, J. C. Batsale, A. Oustaloup et al., Utilisation de mod??les d'identification non entiers pour la r??solution de probl??mes inverses en conduction, International Journal of Thermal Sciences, vol.39, issue.3, pp.374-389, 2000.
DOI : 10.1016/S1290-0729(00)00220-9

J. L. Battaglia, O. Cois, L. Puigsegur, and A. Oustaloup, Solving an inverse heat conduction problem using a non-integer identified model, International Journal of Heat and Mass Transfer, vol.44, issue.14, pp.2671-2680, 2001.
DOI : 10.1016/S0017-9310(00)00310-0

J. L. Battaglia, H. Elmoussami, and L. Puigsegur, Mod??lisation du comportement thermique d'un outil de fraisage : approche par identification de syst??me non entier, Comptes Rendus M??canique, vol.330, issue.12, pp.857-864, 2002.
DOI : 10.1016/S1631-0721(02)01542-5

J. L. Battaglia, L. Puigsegur, and A. Kusiak, Repr??sentation non enti??re du transfert de chaleur par diffusion. Utilit?? pour la caract??risation et le contr??le non destructif thermique, International Journal of Thermal Sciences, vol.43, issue.1, pp.69-85, 2004.
DOI : 10.1016/S1290-0729(03)00104-2

A. Bayoumi, E. Xie, and J. Q. , Some metallurgical aspects of chip formation in cutting Ti-6wt.%Al-4wt.%V alloy, Materials Science and Engineering: A, vol.190, issue.1-2, pp.173-180, 1995.
DOI : 10.1016/0921-5093(94)09595-N

T. Belytschko, J. Ong, W. Liu, and J. Kennedy, Hourglass control in linear and nonlinear problems, Computer Methods in Applied Mechanics and Engineering, vol.43, issue.3, pp.251-276, 1984.
DOI : 10.1016/0045-7825(84)90067-7

T. Belytschko and L. Bindeman, Assumed strain stabilization of the 4-node quadrilateral with 1-point quadrature for nonlinear problems, Computer Methods in Applied Mechanics and Engineering, vol.88, issue.3, pp.311-351, 1991.
DOI : 10.1016/0045-7825(91)90093-L

B. Bhushan, Temperature and friction of sliding sufaces, 1971.

H. Blok, Theoretical study of temperature rise at surfaces of actual contact under oiliness lubricating conditions, Proc. of the General Discussion on Lubrication and Lubricants, 1937.

G. Boothroyd, Temperatures in orthogonal metal cutting, Proc. Inst. Eng, vol.177, pp.789-802, 1963.

J. Brocail, M. Watremez, and L. Dubar, Identification of a friction model for modelling of orthogonal cutting, International Journal of Machine Tools and Manufacture, vol.50, issue.9, pp.807-814, 2010.
DOI : 10.1016/j.ijmachtools.2010.05.003

P. Bussetta, Modélisation et résolution du problème de contact mécanique, Thèse de doctorat de l'Université du Québec à Chicoutimi, 2009.

M. Calamaz, D. Coupard, and F. Girot, A new material model for 2D numerical simulation of serrated chip formation when machining titanium alloy Ti???6Al???4V, International Journal of Machine Tools and Manufacture, vol.48, issue.3-4, pp.275-288, 2008.
DOI : 10.1016/j.ijmachtools.2007.10.014

URL : https://hal.archives-ouvertes.fr/hal-00911076

E. Ceretti, L. Filice, D. Umbrello, and F. Micari, ALE Simulation of Orthogonal Cutting: a New Approach to Model Heat Transfer Phenomena at the Tool-Chip Interface, CIRP Annals, vol.56, issue.1, pp.69-72, 2007.
DOI : 10.1016/j.cirp.2007.05.019

M. Cooper, G. Mikic, B. , B. Yovanovich, M. et al., Thermal contact conductance, Thermal contact conductance, pp.279-300, 1969.
DOI : 10.1016/0017-9310(69)90011-8

M. For83-]-fortin and R. Glowinski, Augmented Lagrangian Methods. Applications to the numerical solution of boundary value problems, 1983.

M. A. Davies, T. J. Burns, and C. J. Evans, On the Dynamics of Chip Formation in Machining Hard Metals, CIRP Annals, vol.46, issue.1, pp.25-30, 1997.
DOI : 10.1016/S0007-8506(07)60768-9

J. Denape and N. Laraqi, Aspect thermique du frottement: mise en ??vidence exp??rimentale et ??l??ments de mod??lisation, M??canique & Industries, vol.1, issue.6, pp.563-579, 2000.
DOI : 10.1016/S1296-2139(00)01068-X

C. Din08-]-dinc, I. Lazoglu, and A. Serpenguzel, Analysis of thermal fields in orthogonal machining with infrared imaging, Journal of Materials Processing Technology, vol.198, issue.1-3, pp.147-154, 2008.
DOI : 10.1016/j.jmatprotec.2007.07.002

J. Dör03-]-dörr, T. Mertens, G. Engering, and M. Lahres, In-situ temperature measurement to determine the machining potential of different tool coatings, Surface and Coatings Technology, pp.174-175, 2003.

D. Dudzinski and A. Molinari, A modelling of cutting for viscoplastic materials, International Journal of Mechanical Sciences, vol.39, issue.4, pp.369-389, 1997.
DOI : 10.1016/S0020-7403(96)00043-4

K. F. Eldridge, O. W. Dillon, and W. Y. Lu, Thermo-viscoplastic finite element modeling of machining under various cutting conditions, Trans NAMRI/SME, vol.XIX, pp.162-169, 1991.

L. Fil07-]-filice, F. Micari, S. Rizzuti, and D. Umbrello, A critical analysis on the friction modelling in orthogonal machining, International Journal of Machine Tools and Manufacture, vol.47, issue.3-4, pp.709-714, 2007.
DOI : 10.1016/j.ijmachtools.2006.05.007

D. P. Fla81-]-flanagan and T. Belytschko, A uniform strain hexahedron and quadrilateral with orthogonal hourglass control, International Journal for Numerical Methods in Engineering, vol.2, issue.5, pp.679-706, 1981.
DOI : 10.1016/B978-0-12-253250-4.50008-7

P. Gilormini, Contribution à la modélisation de la formation du copeau en usinage des métaux, Thèse de Doctorat, 1982.

Y. B. Guo and D. W. Yen, A FEM study on mechanisms of discontinuous chip formation in hard machining, Journal of Materials Processing Technology, vol.155, issue.156, pp.155-156, 2004.
DOI : 10.1016/j.jmatprotec.2004.04.210

G. Chern, Development of a new and simple quick-stop device for the study on chip formation, International Journal of Machine Tools and Manufacture, vol.45, issue.7-8, pp.789-794, 2005.
DOI : 10.1016/j.ijmachtools.2004.11.013

B. Haddag, S. Atlati, M. Nouari, and M. Zenasni, Finite element formulation effect in three-dimensional modeling of a chip formation during machining, International Journal of Material Forming, vol.3, issue.S1, pp.527-530, 2010.
DOI : 10.1007/s12289-010-0823-z

R. S. Hahn, On the temperature developed at the shear plane in the metal cutting process, Proceedings of First US National Congress of Applied Mechanics, pp.661-666, 1951.

F. Heim, Etude de l'influence des paramètres de coupe sur la morphologie du copeau en usinage à très grande vitesse, 1996.

U. Hei11-]-heisel, M. Storchak, P. Eberhard, and T. Gaugele, Experimental studies for verification of thermal effects in cutting, Production Engineering, vol.112, issue.2, pp.507-515, 2011.
DOI : 10.1115/1.2912617

J. Hua and R. Shivpuri, Prediction of chip morphology and segmentation during the machining of titanium alloys, Journal of Materials Processing Technology, vol.150, issue.1-2, pp.124-133, 2004.
DOI : 10.1016/j.jmatprotec.2004.01.028

W. Grzesik and P. Nieslony, A computational approach to evaluate temperature and heat partition in machining with multilayer coated tools, International Journal of Machine Tools and Manufacture, vol.43, issue.13, pp.1311-1317, 2003.
DOI : 10.1016/S0890-6955(03)00160-3

K. Iwa84-]-iwata, K. Osakada, and Y. Terasaka, Process Modeling of Orthogonal Cutting by the Rigid-Plastic Finite Element Method, Journal of Engineering Materials and Technology, vol.106, issue.2, pp.132-138, 1984.
DOI : 10.1115/1.3225687

S. P. Jaspers, J. H. Dautzenberg, and D. A. Taminiau, Temperature measurement in orthogonal metal cutting, The International Journal of Advanced Manufacturing Technology, vol.4, issue.10, pp.7-12, 1998.
DOI : 10.1007/BF01179411

[. Johnson, G. J. Cook, and W. H. , A constitutive model and data for metals subjected to large strains, high strain rates and high temperatures The Hague, Proceedings of the Seventh International Symposium on Ballistics, pp.541-547, 1983.

[. Johnson, G. R. Cook, and W. H. , Fracture characteristics of three metals subjected to various strains, strain rates, temperatures and pressures, Engineering Fracture Mechanics, vol.21, issue.1, pp.31-48, 1985.
DOI : 10.1016/0013-7944(85)90052-9

K. W. Kim, W. Y. Lee, and H. C. Sin, A finite-element analysis of machining with the tool edge considered, Journal of Materials Processing Technology, vol.86, pp.45-55, 1999.

R. Komanduri and R. H. Brown, On the Mechanics of Chip Segmentation In Machining, Journal of Engineering for Industry, vol.103, issue.1, pp.33-51, 1981.
DOI : 10.1115/1.3184458

R. Komanduri and Z. B. Hou, Thermal modeling of the metal cutting process ??? Part II: temperature rise distribution due to frictional heat source at the tool???chip interface, International Journal of Mechanical Sciences, vol.43, issue.1, pp.57-88, 2001.
DOI : 10.1016/S0020-7403(99)00104-6

A. Kusiak, J. L. Battaglia, and R. Marchal, Influence of CrN coating in wood machining from heat flux estimation in the tool, International Journal of Thermal Sciences, vol.44, issue.3, pp.289-301, 2005.
DOI : 10.1016/j.ijthermalsci.2004.08.006

P. Kwon, T. Schiemann, and R. Kountanya, An inverse estimation scheme to measure steady-state tool???chip interface temperatures using an infrared camera, International Journal of Machine Tools and Manufacture, vol.41, issue.7, pp.1015-1030, 2001.
DOI : 10.1016/S0890-6955(00)00113-9

T. Lau93-]-laursen, A. Simo, J. , and C. , A continuum-based finite element formulation for the implicit solution of multibody, large deformation-frictional contact problems, International Journal for Numerical Methods in Engineering, vol.44, issue.20, pp.3451-3485, 1993.
DOI : 10.1137/1.9781611970845

E. Lee51-]-lee, H. Shaffer, B. , and W. , The theory of plasticity applied to the problem of machining, USA American society of mechanical engineers, Journal of Applied Mechanics, vol.18, pp.405-413, 1951.

]. W. Leo54 and . Leone, Distribution of shear zone heat in metal cutting, Trans. of ASME, vol.76, pp.121-125, 1954.

J. Lem91-]-lemaitre, A Continuous Damage Mechanics Model for Ductile Fracture, Journal of Engineering Materials and Technology, vol.107, issue.1, pp.83-89, 1991.
DOI : 10.1115/1.3225775

Z. C. Lin01-]-lin and Y. Y. Lin, Three-dimensional elastic-plastic finite element analysis for orthogonal cutting with discontinuous chip of 6-4 brass, Theoretical and Applied Fracture Mechanics, pp.137-153, 2001.

. Lis03, G. List, M. Nouari, F. Girot, D. Géhin et al., Simulation de la coupe orthogonale de l'Inconel 718: Validation Expérimentale, 2003.

N. Liou, M. Okada, and V. Et-prakash, Formation of molten metal films during metal-on-metal slip under extreme interfacial conditions, Journal of the Mechanics and Physics of Solids, vol.52, issue.9, pp.2025-2056, 2004.
DOI : 10.1016/j.jmps.2004.03.008

E. G. Loe54-]-loewen and . Shaw, On the analysis of cutting tool temperatures, Transactions of ASME, vol.71, pp.217-231

T. Mabrouki, F. Girardin, M. Asad, and J. Rigal, Numerical and experimental study of dry cutting for an aeronautic aluminium alloy (A2024-T351), International Journal of Machine Tools and Manufacture, vol.48, issue.11, pp.2024-351, 2008.
DOI : 10.1016/j.ijmachtools.2008.03.013

URL : https://hal.archives-ouvertes.fr/hal-00383575

A. G. Mam01-]-mamalis, M. Horvath, A. S. Branis, and D. E. Manolakos, Finite element simulation of chip formation in orthogonal metal cutting, Journal of Materials Processing Technology, vol.110, issue.1, 2001.
DOI : 10.1016/S0924-0136(00)00861-X

T. Mar95-]-marusich, D. Ortiz, and M. , Modelling and simulation of high-speed machining, International Journal for Numerical Methods in Engineering, vol.36, issue.18, pp.3675-3694, 1995.
DOI : 10.1007/BF02812022

E. Merchant, Mechanics of the metal cutting process orthogonal cutting, Journal Applied Physics p, pp.318-324, 1945.

Q. Ming, Z. Yong-zhen, and Z. Jun, Effect of friction heat on tribological behavior of M2 steel against GCr15 steel in dry sliding systems, Journal of University of Science and Technology Beijing, Mineral, Metallurgy, Material, vol.14, issue.6, pp.14-512, 2007.
DOI : 10.1016/S1005-8850(07)60119-4

. Mol92, A. Molinari, and D. Dudzinski, Stationary shear band in high speed, C. R, 1992.

. Mol02, A. Molinari, C. Musquar, and G. Sutter, Adiabatic shear banding in high speed machining of Ti?6Al?4V: experiments and modeling, International Journal of Plasticity, vol.18, pp.443-459, 2002.

M. Molinari and A. , The Merchant's model of orthogonal cutting revisited: A new insight into the modeling of chip formation, International Journal of Mechanical Sciences, vol.50, issue.2, pp.124-131, 2008.
DOI : 10.1016/j.ijmecsci.2007.07.015

. Mol11, A. Molinari, R. Cheriguene, and H. Miguelez, Numerical and analytical modeling of orthogonal cutting: The link between local variables and global contact characteristics, International Journal of Mechanical Sciences, vol.53, pp.183-206, 2011.

A. Moufki, A. Molinari, and D. Dudzinski, Modelling of orthogonal cutting with a temperature dependent friction law, Journal of the Mechanics and Physics of Solids, vol.46, issue.10, pp.2103-2138, 1998.
DOI : 10.1016/S0022-5096(98)00032-5

. Nou06 and M. Nouari, Contribution à la compréhension et à la modélisation des mécanismes d'usure dans un contact à sec en conditions de chargement complexe: Application à l'usinage des alliages aéronautiques, 2006.

M. Nouari, M. Calamaz, and F. Girot, M??canismes d'usure des outils coupants en usinage ?? sec de l'alliage de titane a??ronautique Ti???6Al???4V, Comptes Rendus M??canique, vol.336, issue.10, pp.772-781, 2008.
DOI : 10.1016/j.crme.2008.07.007

Y. Ohbuchi and T. Obikawa, Finite Element Modeling of Chip Formation in the Domain of Negative Rake Angle Cutting, Journal of Engineering Materials and Technology, vol.31, issue.3, pp.32-332, 2003.
DOI : 10.1115/1.3629585

Y. Ohbuchi and T. Obikawa, Adiabatic shear in chip formation with negative rake angle, International Journal of Mechanical Sciences, vol.47, issue.9, pp.1377-1392, 2005.
DOI : 10.1016/j.ijmecsci.2005.05.003

D. R. Owen, J. Vaz, and M. , Computational techniques applied to high-speed machining under adiabatic strain localization conditions, Computer Methods in Applied Mechanics and Engineering, vol.171, issue.3-4, pp.445-461, 1999.
DOI : 10.1016/S0045-7825(98)00220-5

P. Oxl89-]-oxley, L. , and B. , Mechanics of Machining: An Analytical Approach to Assessing Machinability, Journal of Applied Mechanics, vol.57, issue.1, 1989.
DOI : 10.1115/1.2888318

. Ozl09, E. Ozlu, E. Budak, and A. Molinari, Analytical and experimental investigation of rake contact and friction behaviour in metal cutting, International Journal of Machine Tools and Manufacture, vol.49, pp.865-875, 2009.

O. Pan05-]-pantalé, Plateforme de prototypage virtuel pour la simulation numérique en Grandes Transformations Thermomécaniques Rapides, 2005.

N. Pauze, Fatigue corrosion dans le sens travers court de tôles d'aluminium 2024-T351 présentant des défauts de corrosion localisée, 2008.

R. S. Pawade, . Sonawane, A. Harshad, . Joshi, and S. Suhas, An analytical model to predict specific shear energy in high-speed turning of Inconel 718, International Journal of Machine Tools and Manufacture, vol.49, issue.12-13, pp.979-990, 2009.
DOI : 10.1016/j.ijmachtools.2009.06.007

F. Pen09-]-pennec, Modélisation du contact métal-métal: application aux microcommutateurs MEMS RF, 2009.

G. Pou99-]-poulachon, Aspect phénoménologiques, mécaniques et métallurgiques en tournage c-BN des aciers durcis. Application : usinabilité de l'acier 100Cr6, 1999.

L. Pui02-]-puigsegur, Caractérisation thermique d'un procédé d'usinage par tournage. Approche analytique et par identification se systèmes non entiers, 2002.

J. Rech, A. Kusiak, and J. L. Battaglia, Tribological and thermal functions of cutting tool coatings, Surface and Coatings Technology, vol.186, issue.3, pp.364-371, 2004.
DOI : 10.1016/j.surfcoat.2003.11.027

A. N. Reznikov, Thermophysical aspects of metal cutting processes, 1981.

S. Rhim and S. Oh, Prediction of serrated chip formation in metal cutting process with new flow stress model for AISI 1045 steel, Journal of Materials Processing Technology, vol.171, issue.3, pp.417-422, 2006.
DOI : 10.1016/j.jmatprotec.2005.08.002

G. S. Sek93-]-sekhon and J. L. Chenot, NUMERICAL SIMULATION OF CONTINUOUS CHIP FORMATION DURING NON???STEADY ORTHOGONAL CUTTING, Engineering Computations, vol.24, issue.1, pp.31-48, 1993.
DOI : 10.1002/nme.1620241107

M. C. Shaw and A. Vyas, The Mechanism of Chip Formation with Hard Turning Steel, CIRP Annals, vol.47, issue.1, pp.77-82, 1998.
DOI : 10.1016/S0007-8506(07)62789-9

M. C. Shaw, Metal cutting principles, Tribology International, vol.18, issue.1, 1989.
DOI : 10.1016/0301-679X(85)90013-1

URL : https://babel.hathitrust.org/cgi/imgsrv/download/pdf?id=wu.89042722868;orient=0;size=100;seq=9;attachment=0

. Sig33 and A. Signorini, Sopra alcune questioni di statica dei sistemi continui, pp.231-251, 1933.

. Son87, S. Song, and M. M. Yovanovich, Explicit relative contact pressure expression: Dependence upon surface roughness parameters and vickers microhardness coefficients, AIAA Journal, pp.87-0152, 1987.

. Sow89, R. Sowerby, and N. Chandrasekaran, A proposal for the onset of chip segmentation in machining Tool temperature in interrupted metal cutting, Materials Science and Engineering: A Journal of Engineering for Industry, Transaction of the ASME, vol.119, issue.114, pp.219-229, 1989.

S. Sun09-]-sun, M. Brandt, and M. S. Dargusch, Characteristics of cutting forces and chip formation in machining of titanium alloys, International Journal of Machine Tools and Manufacture, vol.49, issue.7-8, pp.561-568, 2009.
DOI : 10.1016/j.ijmachtools.2009.02.008

G. Sutter, L. Faure, A. Molinari, A. Delime, and D. Duidzinski, Experimental Analysis of the Cutting Process and Chip Formation at High Speed Machining, Le Journal de Physique IV, vol.07, issue.C3, pp.33-37, 1997.
DOI : 10.1051/jp4:1997308

URL : https://hal.archives-ouvertes.fr/jpa-00255381

. Sut05, G. Sutter, and A. Molinari, Analysis of the Cutting Force Components and Friction in High Speed Machining, Journal of Manufacturing Science and Engineering, vol.127, pp.245-250, 2005.

X. Tia93-]-tian, K. , J. , F. , and E. , Contact Surface Temperature Models for Finite Bodies in Dry and Boundary Lubricated Sliding, Journal of Tribology, vol.115, issue.3, pp.411-418, 1993.
DOI : 10.1115/1.2921652

K. J. Tri51-]-trigger and B. T. Chao, An analytical evaluation of metal cutting temperatures, Transactions of ASME, vol.73, pp.57-68, 1951.

D. Umbrello, L. Filice, S. Rizzuti, and F. Micari, On the evaluation of the global heat transfer coefficient in cutting, International Journal of Machine Tools and Manufacture, vol.47, issue.11, pp.1738-1743, 2007.
DOI : 10.1016/j.ijmachtools.2006.12.002

D. Umbrello, Finite element simulation of conventional and high speed machining of Ti6Al4V alloy, Journal of Materials Processing Technology, vol.196, issue.1-3, pp.79-87, 2008.
DOI : 10.1016/j.jmatprotec.2007.05.007

E. Usui and T. Shirakashi, Mechanics of machining from " descriptive " to " predictive " theory On the art of cutting metals- 75 years later: a tribute to F.W. Taylor, Proceedings of the winter annual meeting of the American Society of Mechanical Engineers.PED, pp.13-35, 1982.

D. Werschmoeller and X. Li, Measurement of tool internal temperatures in the tool???chip contact region by embedded micro thin film thermocouples, Journal of Manufacturing Processes, vol.13, issue.2, pp.147-152, 2011.
DOI : 10.1016/j.jmapro.2011.05.001

P. Wriggers, C. Miehe, M. Kleiber, and J. Simo, On the coupled thermomechanical treatment of necking problems via finite element methods, International Journal for Numerical Methods in Engineering, vol.1, issue.4, pp.869-883, 1992.
DOI : 10.1115/1.3422829

P. Wriggers and C. Miehe, Contact constraints within coupled thermomechanical analysis???A finite element model, Computer Methods in Applied Mechanics and Engineering, vol.113, issue.3-4, pp.301-319, 1994.
DOI : 10.1016/0045-7825(94)90051-5

URL : https://hal.archives-ouvertes.fr/hal-01574175

P. Wriggers, Computational contact mechanics, 2006.
URL : https://hal.archives-ouvertes.fr/hal-00466790

V. M. Jr, D. R. Owen, V. Kalhori, M. Lundblad, and L. E. Lindgren, Modelling and Simulation of Machining Processes, Arch Comput Methods Eng, vol.14, pp.173-204, 2007.

C. Vergne, Analyse de l'influence des oxydes dans le frottement d'une fonte pour outil de travail à chaud, 2001.

. Vie70 and G. Vieregge, Zerspanung der Eisenwerkstoffe. Stahleisen mbH, Manufacturing Processes 1 Cutting, 1970.

J. Q. Xie, A. E. Bayoumi, and H. M. Zbib, A study on shear banding in chip formation of orthogonal machining, International Journal of Machine Tools and Manufacture, vol.36, issue.7, pp.835-847, 1996.
DOI : 10.1016/0890-6955(95)00016-X

X. Yang and C. R. Liu, A new stress-based model of friction behavior in machining and its significant impact on residual stresses computed by finite element method, International Journal of Mechanical Sciences, vol.44, issue.4, pp.703-723, 2002.
DOI : 10.1016/S0020-7403(02)00008-5

F. Yuan, N. Liou, and V. Et-prakash, High-speed frictional slip at metal-on-metal interfaces, International Journal of Plasticity, vol.25, issue.4, pp.612-634, 2009.
DOI : 10.1016/j.ijplas.2008.12.006

F. J. Zer87-]-zerilli and R. W. Armstrong, Dislocation???mechanics???based constitutive relations for material dynamics calculations, Journal of Applied Physics, vol.46, issue.5, pp.1816-1825, 1987.
DOI : 10.1063/1.1707363

N. N. Zor63-]-zorev, Interrelationship between shear processes occurring along tool face and on shear plane in metal cutting, Proceedings of the international research in production engineering conference. ASME, pp.42-49, 1963.

S. Thèse-de, ATLATI : Développement d'une nouvelle approche hybride pour la modélisation des échanges thermiques à l'interface outilcopeau : application à l'usinage de l'alliage d'aluminium