S. Denis, P. Archambault, E. Gautier, A. Simon, and G. Beck, Prediction of residual stress and distortion of ferrous and non-ferrous metals: Current status and future developments, Journal of Materials Engineering and Performance, vol.347, issue.9, pp.92-102, 2002.
DOI : 10.1179/026708395790164995

L. Mangin, Etude et simulation des processus de déformation au cours du chauffage de tubes d'acier : prise en compte des couplages fluide -thermique -métallurgie -mécanique, Thèse de l'Institut National Polytechnique de Lorraine, 2010.

A. Kouachi, Etude expérimentale de l'ébullition convective d'un jet d'eau plan impactant une surface mobile portée à hautes températures, Thèse de l'Université Henri Poincaré, 2006.

J. Douce, Modélisation de la trempe gazeuse haute pression -Application aux aciers de cémentation et de trempe, Thèse de l'Institut National Polytechnique de Lorraine, 2008.

D. H. Wolf, F. P. Incropera, and R. Viskanta, Jet Impingement Boiling, Advances in Heat Transfer, vol.23, pp.1-132, 1993.
DOI : 10.1016/S0065-2717(08)70005-4

H. Robidou, Etude expérimentale du refroidissement diphasique à haute température par jet d'eau impactant, Thèse de l'Université Henri Poincaré, 2000.

N. Karwa, Experimental study of water jet impingement cooling of hot steel plates

S. Nukiyama, The maximum and minimum values of the heat Q transmitted from metal to boiling water under atmospheric pressure, International Journal of Heat and Mass Transfer, vol.9, issue.12, pp.1419-1433, 1966.
DOI : 10.1016/0017-9310(66)90138-4

D. T. Vader, Convective and boiling heat transfer from a heated surface to an impinging, planar jet of water, 1988.

S. Ishigai, S. Nakanishi, and T. Ochi, Boiling heat transfer for a plane water jet impinging on a hot surface, pp.445-450, 1978.

B. D. Piggott, E. P. White, and R. B. Duffey, Wetting delay due to film and transition boiling on hot surfaces, Nuclear Engineering and Design, vol.36, issue.2, pp.169-181, 1976.
DOI : 10.1016/0029-5493(76)90003-0

M. A. Islam, M. Monde, P. L. Woodfield, and Y. Mitsutake, Jet impingement quenching phenomena for hot surfaces well above the limiting temperature for solid???liquid contact, International Journal of Heat and Mass Transfer, vol.51, issue.5-6, pp.5-6, 2008.
DOI : 10.1016/j.ijheatmasstransfer.2007.01.059

L. Bogdanic, H. Auracher, and F. Ziegler, Two-phase structure above hot surfaces in jet impingement boiling, Heat and Mass Transfer, vol.46, issue.7, pp.1019-1028, 2009.
DOI : 10.1007/s00231-007-0272-5

M. M. Prieto, L. S. Ruiz, and J. A. Menendez, Thermal performance of numerical model of hot strip mill runout table, Ironmaking & Steelmaking, vol.56, issue.6, pp.474-480, 2001.
DOI : 10.1179/mst.1991.7.4.360

R. Viskanta and T. Bergman, Heat transfer in material processing " Handbook of heat transfer, 1998.

W. Timm, K. Weinzierl, and A. Leipertz, Heat transfer in subcooled jet impingement boiling at high wall temperatures, International Journal of Heat and Mass Transfer, vol.46, issue.8, pp.1385-1393, 2003.
DOI : 10.1016/S0017-9310(02)00416-7

H. Leocadio, J. C. Passos, and A. F. Da-silva, Heat transfer behavior of a high temperature steel plate cooled by a subcooled impinging circular water jet " proceeding of the 7th ECI International Conference on Boiling Heat Transfer, 2009.

J. Hammad, Y. Mitsutake, and M. Monde, Movement of maximum heat flux and wetting front during quenching of hot cylindrical block, International Journal of Thermal Sciences, vol.43, issue.8, pp.743-752, 2004.
DOI : 10.1016/j.ijthermalsci.2004.02.014

A. K. Mozumder, M. Monde, and P. L. Woodfield, Delay of wetting propagation during jet impingement quenching for a high temperature surface, International Journal of Heat and Mass Transfer, vol.48, issue.25-26, pp.25-26, 2005.
DOI : 10.1016/j.ijheatmasstransfer.2005.06.034

A. K. Mozumder, Thermal and hydrodynamic characteristics of jet impingement quenching for high temperature surface, 2006.

P. L. Woodfield, A. K. Mozumder, and M. Monde, On the size of the boiling region in jet impingement quenching, International Journal of Heat and Mass Transfer, vol.52, issue.1-2, pp.460-465, 2009.
DOI : 10.1016/j.ijheatmasstransfer.2008.05.024

L. Chai, M. Shoji, and X. Peng, Dry patch interaction caused by lateral conduction in transition boiling, International Journal of Heat and Mass Transfer, vol.44, issue.21, pp.4169-4173, 2001.
DOI : 10.1016/S0017-9310(01)00060-6

D. P. Jordan, Film and Transition Boiling Advances in Heat Transfer, pp.55-128, 1969.

L. C. Witte and J. H. Lienhard, On the existence of two ???transition??? boiling curves, International Journal of Heat and Mass Transfer, vol.25, issue.6, pp.771-779, 1982.
DOI : 10.1016/0017-9310(82)90089-8

N. Hatta, J. Kokado, and K. Hanasaki, Numerical Analysis of Cooling Characteristics for Water Bar, Transactions of the Iron and Steel Institute of Japan, vol.23, issue.7, pp.555-564, 1983.
DOI : 10.2355/isijinternational1966.23.555

M. Gradeck, A. Kouachi, J. L. Borean, P. Gardin, and M. Lebouché, Heat transfer from a hot moving cylinder impinged by a planar subcooled water jet, International Journal of Heat and Mass Transfer, vol.54, pp.25-26, 2011.
DOI : 10.1016/j.ijheatmasstransfer.2011.07.038

URL : https://hal.archives-ouvertes.fr/hal-01579238

N. Seiler-marie, Modélisation et simulation des phénomènes d'ébullition et du transfert de chaleur dans la zone d'impact d'un jet sur une plaque chaude, Thèse de l' Institut National Polytechnique de Toulouse, 2004.

P. Zhang, Study of boiling heat transfer on a stationary downward facing hot steel plate cooled by a circular water jet, 2004.

M. Gradeck, A. Kouachi, A. Dani, D. Arnoult, and J. L. Boréan, Experimental and numerical study of the hydraulic jump of an impinging jet on a moving surface, Experimental Thermal and Fluid Science, vol.30, issue.3, pp.193-201, 2006.
DOI : 10.1016/j.expthermflusci.2005.05.006

URL : https://hal.archives-ouvertes.fr/hal-01579183

M. Gradeck, A. Kouachi, M. Lebouché, F. Volle, D. Maillet et al., Boiling curves in relation to quenching of a high temperature moving surface with liquid jet impingement, International Journal of Heat and Mass Transfer, vol.52, issue.5-6, pp.5-6, 2009.
DOI : 10.1016/j.ijheatmasstransfer.2008.09.015

URL : https://hal.archives-ouvertes.fr/hal-01580004

C. Bartoli, P. D. Marco, and S. Faggiani, Heat transfer and flow pattern at a cylinder impinged by a slot jet during incipient and nucleate boiling, Experimental Thermal and Fluid Science, vol.15, issue.2, pp.101-108, 1997.
DOI : 10.1016/S0894-1777(97)00050-2

Y. Miyasaka and S. Inada, The effect of pure forced convection on the boiling heat transfer between a two-dimensional subcooled water jet and a heated surface., Journal of Chemical Engineering of Japan, vol.13, issue.1, pp.29-35, 1980.
DOI : 10.1252/jcej.13.22

M. Monde and Y. Katto, Burnout in a high heat-flux boiling system with an impinging jet, International Journal of Heat and Mass Transfer, vol.21, issue.3, pp.295-305, 1978.
DOI : 10.1016/0017-9310(78)90122-9

Y. Qiu and Z. Liu, Critical heat flux of steady boiling for saturated liquids jet impinging on the stagnation zone, International Journal of Heat and Mass Transfer, vol.48, issue.21-22, pp.21-22, 2005.
DOI : 10.1016/j.ijheatmasstransfer.2005.06.002

Z. Liu and Q. Zhu, Prediction of Critical Heat Flux for Convective Boiling of Saturated Water Jet Impinging on the Stagnation Zone, Journal of Heat Transfer, vol.23, issue.6, p.1125, 2002.
DOI : 10.1016/0017-9310(80)90140-4

M. Masanori and O. Yoshiaki, Critical heat flux in saturated forced convective boiling on a heated disk with an impinging jet???CHF in L-regime, International Journal of Heat and Mass Transfer, vol.28, issue.3, pp.547-552, 1985.
DOI : 10.1016/0017-9310(85)90177-2

Z. H. Liu, Prediction of Minimum Heat Flux for Water Jet Boiling on a Hot Plate, Journal of Thermophysics and Heat Transfer, vol.45, issue.1, pp.159-165, 2003.
DOI : 10.1016/0017-9310(87)90085-8

J. Kokado, N. Hatta, J. Harada, H. Takuda, and N. Yasuhira, An analysis of film boiling phenomena of subcooled water spreading radially on a hot steel plate, Archiv f??r das Eisenh??ttenwesen, vol.70, issue.4, 1984.
DOI : 10.2355/tetsutohagane1955.68.8_974

M. Gradeck, A. Kouachi, J. L. Borean, P. Gardin, and M. Lebouché, Heat transfer from a hot moving cylinder impinged by a planar subcooled water jet, International Journal of Heat and Mass Transfer, vol.54, pp.25-26, 2011.
DOI : 10.1016/j.ijheatmasstransfer.2011.07.038

URL : https://hal.archives-ouvertes.fr/hal-01579238

F. Volle, Conduction inverse sur un cylindre en rotation -Cas de l'ébullition convective induite par l'impact d'un jet d'eau, Thèse de l'Université Henri Poincaré, 2006.

F. Volle, D. Maillet, M. Gradeck, A. Kouachi, and M. Lebouché, Practical application of inverse heat conduction for wall condition estimation on a rotating cylinder, International Journal of Heat and Mass Transfer, vol.52, issue.1-2, pp.210-221, 2009.
DOI : 10.1016/j.ijheatmasstransfer.2008.05.025

URL : https://hal.archives-ouvertes.fr/hal-01579217

J. V. Beck, B. Blackwell, C. St, and . Clair, Inverse Heat Conduction, ill posed problems, 1985.

G. Blanc and M. Raynaud, Solution of the Inverse Heat Conduction Problem From Thermal Strain Measurements, Journal of Heat Transfer, vol.82, issue.4, pp.842-849, 1996.
DOI : 10.1115/1.3679871

M. Z. Podowski and R. Podowski, Mechanistic Multidimensional Modeling of Forced Convection Boiling Heat Transfer, Science and Technology of Nuclear Installations, vol.14, 2009.
DOI : 10.1016/0301-9322(85)90059-X

N. Basu, G. R. Warrier, and V. K. Dhir, Wall Heat Flux Partitioning During Subcooled Flow Boiling: Part 1???Model Development, Journal of Heat Transfer, vol.18, issue.2, pp.131-140, 2005.
DOI : 10.1115/1.3684339

N. Basu, G. R. Warrier, and V. K. Dhir, Wall heat flux partioning during subcooled flow boiling : Part 2 -model validation, J. of Heat Transfer, pp.141-148, 2005.

M. Montout, Contribution au développement d'une approche prédictive locale de la crise d'ébullition, Thèse de l'Institut National Polytechnique de Toulouse, 2009.

R. Kopun, D. Greif, Z. Kovacic, and M. Suffa, Numerical investigation of the immersion quenching process for heat treated parts using an eulerian multi-fluid approach, proceeding of the 10th Int. Conf. on CFD in Oil & Gas, Metallurgical and Process Industries, 2014.

A. Mulayim, S. Eroglu, U. Weiss, E. Prabhu, J. Jan et al., Experimental and numerical investigation of water quench cooling of aluminum cylinder heads, proceeding of the 5th Int. Conf. on Thermal Process Modeling and Computer Simulation, pp.276-283, 2014.

V. H. Valle and D. B. Kenning, Subcooled flow boiling at high heat flux, International Journal of Heat and Mass Transfer, vol.28, issue.10, pp.1907-1920, 1985.
DOI : 10.1016/0017-9310(85)90213-3

P. Stark, B. Hinrichs, N. Hornig, S. Schuettenberg, and U. Fritsching, Simulation of quenching process with liquid jets, Proceedings from the 6th International Quenching and Control Distortion Conference Including the 4th International Distortion Engineering Conference, 2012.

S. Narumanchi, A. Troshko, D. Bharathan, and V. Hassani, Numerical simulations of nucleate boiling in impinging jets: Applications in power electronics cooling, International Journal of Heat and Mass Transfer, vol.51, issue.1-2, pp.1-12, 2008.
DOI : 10.1016/j.ijheatmasstransfer.2007.05.026

E. Group, Manuel de référence Sysweld, 2000.

S. Denis, D. Farias, and A. Simon, Mathematical Model Coupling Phase Transformations and Temperature Evolutions in Steels., ISIJ International, vol.32, issue.3, pp.316-325, 1992.
DOI : 10.2355/isijinternational.32.316

F. Fernandes, S. Denis, and A. Simon, Prévision de l'évolution thermique et structurale des aciers au cours de leur refroidissement continu, Mémoires Études Sci, pp.355-366, 1986.

D. Farias, Traitement thermique laser de l'acier XC 42 et modélisation des transformations de phases en cycles rapides au chauffage et au refroidissement, Thèse de l'Institut National Polytechnique de Lorraine, 1991.

A. Mey, Prévision par le calcul des cinétiques de transformation de phases et des contraintes internes lors du traitement thermique des aciers cémentés, Thèse de l'Institut National Polytechnique de Lorraine, 1997.

W. A. Johnson and R. Mehl, Reaction kinetics in processes of nucleation and growth, Trans AIME 135 pp, pp.416-442, 1939.

M. Avrami, Kinetics of Phase Change. I General Theory, The Journal of Chemical Physics, vol.22, issue.12, pp.1103-1112, 1939.
DOI : 10.1002/zaac.19332140411

E. Scheil, Anlaufzeit der Austenitumwandlung, Arch. Eisenhüttenwes, pp.565-567, 1935.
DOI : 10.1002/srin.193500186

D. Koistinen and R. Marburger, A general equation prescribing the extent of the austenite-martensite transformation in pure iron-carbon alloys and plain carbon steels, Acta Metallurgica, vol.7, issue.1, pp.59-60, 1959.
DOI : 10.1016/0001-6160(59)90170-1

J. Leblond, G. Mottet, and J. Devaux, Mathematical modelling of transformation plasticity in steels I: Case of ideal-plastic phases, International Journal of Plasticity, vol.5, issue.6, pp.551-572, 1989.
DOI : 10.1016/0749-6419(89)90001-6

J. Leblond, J. Devaux, and J. Devaux, Mathematical modelling of transformation plasticity in steels II: Coupling with strain hardening phenomena, International Journal of Plasticity, vol.5, issue.6, pp.573-591, 1989.
DOI : 10.1016/0749-6419(89)90002-8

Y. Vincent, Simulation numérique des conséquences métallurgiques et mécaniques induite par une opération de soudage

M. Veaux, Etude expérimentale et prévision par le calcul des cinétiques de transformation de phases, des contraintes résiduelles et des déformations lors de la transformation bainitique, 2003.

G. Vidal, P. Lescop, and L. Raymondin, Influence de la temp??rature sur les constantes ??lastiques des m??taux et alliages, XL VIII, 1951.
DOI : 10.1051/metal/195148110864

R. Wendelstorf, K. H. Spitzer, and J. Wendelstorf, Effect of oxide layers on spray water cooling heat transfer at high surface temperatures, International Journal of Heat and Mass Transfer, vol.51, issue.19-20, pp.19-20, 2008.
DOI : 10.1016/j.ijheatmasstransfer.2008.01.033