S. A. Spiewak, Acceleration based indirect force measurement in metal cutting processes, International Journal of Machine Tools and Manufacture, vol.35, issue.1, pp.1-17, 1995.
DOI : 10.1016/0890-6955(95)80005-0

K. A. Risbood, U. S. Dixit, and A. D. Sahasrabudhe, Prediction of surface roughness and dimensional deviation by measuring cutting forces and vibrations in turning process, Journal of Materials Processing Technology, vol.132, issue.1-3, pp.203-214, 2002.
DOI : 10.1016/S0924-0136(02)00920-2

D. A. Axinte, W. Belluco, and L. De-chiffre, Evaluation of cutting force uncertainty components in turning, International Journal of Machine Tools and Manufacture, vol.41, issue.5, pp.719-730, 2000.
DOI : 10.1016/S0890-6955(00)00095-X

S. Sastry, S. G. Kapoor, and R. E. Devor, Compensation of progressive radial run-out in face-milling by spindle speed variation, International Journal of Machine Tools and Manufacture, vol.40, issue.8, pp.1121-1139, 2000.
DOI : 10.1016/S0890-6955(99)00115-7

F. Lapoujolade, Measuring of cutting forces during fast transient periods, 1ier French and German Conference on High Speed Machining, pp.372-376, 1997.

F. Lapoujoulade, G. Coffignal, and J. Pimont, Cutting forces evaluation during high speed milling, 2ème Conf. Int. IDMME'98 Compiègne -France, pp.27-29, 1998.

N. Tounsi and A. Otho, Dynamic cutting force measuring, International Journal of Machine Tools and Manufacture, vol.40, issue.8, pp.1157-1170, 2000.
DOI : 10.1016/S0890-6955(99)00117-0

N. Tounsi and A. Otho, Identification of machine???tool???workpiece system dynamics, International Journal of Machine Tools and Manufacture, vol.40, issue.9, pp.1367-1384, 1999.
DOI : 10.1016/S0890-6955(99)00123-6

S. Chen, Q. Luo, P. W. Wagstaff, and J. C. Henrio, Caractérisation des forces dynamiques de coupe en usinage a l'aide des mesures indirectes, Actes de 4ième Congres Franc-ais d'Acoustique, pp.14-18, 1997.

M. T. Hayajneh, V. P. Astakhov, and M. O. Osman, An analytical evaluation of the cutting forces in orthogonal cutting using a dynamic model of the shear zone with parallel boundaries, Journal of Materials Processing Technology, vol.82, issue.1-3, pp.61-77, 1999.
DOI : 10.1016/S0924-0136(98)00021-1

I. Minis and B. S. Berger, Modeling, analysis, of characterization of machining dynamics, Dynamics and Chaos in Manufacturing Processes, 1998.

L. R. Castro, P. Viéville, and P. Lipinski, Correction of dynamic effects on force measurements made with piezoelectric dynamometers, International Journal of Machine Tools and Manufacture, vol.46, issue.14, pp.1707-1715, 2006.
DOI : 10.1016/j.ijmachtools.2005.12.006

D. J. Ewins, Modal Testing : Theory, Practice and Application, 2000.

A. Girard and E. Cavro, Identification modale d'un spécimen sur vibrateur, Actes du XV e Colloque Vibrations Chocs et Bruit, pp.14-16, 2006.

P. B. Oxley, Mechanics of Machining: An Analytical Approach to Assessing Machinability, Journal of Applied Mechanics, vol.57, issue.1, 1989.
DOI : 10.1115/1.2888318

Y. Altintas, Manufacturing Automation: metal cutting mechanics, machine tool vibrations, and CNC design, 2000.
DOI : 10.1017/CBO9780511843723

R. Komanduri, V. Turkovich, and B. F. , New observations on the mechanism of chip formation when machining titanium alloys, Wear, vol.69, issue.2, pp.179-188, 1981.
DOI : 10.1016/0043-1648(81)90242-8

. Komanduri, Some clarifications on the mechanics of chip formation when machining titanium alloys, Wear, vol.76, issue.1, pp.15-34, 1982.
DOI : 10.1016/0043-1648(82)90113-2

A. E. Bayoumi and J. Q. Xie, Some metallurgical aspects of chip formation in cutting Ti-6wt.%Al-4wt.%V alloy, Materials Science and Engineering: A, vol.190, issue.1-2, pp.173-180, 1995.
DOI : 10.1016/0921-5093(94)09595-N

J. Barry, V. Byrne, and D. Lennon, Observations on chip formation and acoustic emission in machining Ti???6Al???4V alloy, International Journal of Machine Tools and Manufacture, vol.41, issue.7, pp.1055-1070, 2001.
DOI : 10.1016/S0890-6955(00)00096-1

A. Molinari, V. Musquar, and G. Sutter, Adiabatic shear banding in high speed machining of Ti???6Al???4V: experiments and modeling, International Journal of Plasticity, vol.18, issue.4, pp.443-459, 2002.
DOI : 10.1016/S0749-6419(01)00003-1

J. Hua and R. Shivpuri, Prediction of chip morphology and segmentation during the machining of titanium alloys, Journal of Materials Processing Technology, vol.150, issue.1-2, pp.124-133, 2004.
DOI : 10.1016/j.jmatprotec.2004.01.028

C. H. Che-haron and A. Jawaid, The effect of machining on surface integrity of titanium alloy Ti???6% Al???4% V, Journal of Materials Processing Technology, vol.166, issue.2, pp.188-192, 2005.
DOI : 10.1016/j.jmatprotec.2004.08.012

R. Komanduri, T. Schroeder, J. Hazra, V. Turkovich, B. F. Flom et al., On the Catastrophic Shear Instability in High-Speed Machining of an AISI 4340 Steel, Journal of Engineering for Industry, vol.104, issue.2, pp.121-131, 1982.
DOI : 10.1115/1.3185807

J. Barry and G. Byrne, The Mechanisms of Chip Formation in Machining Hardened Steels, Journal of Manufacturing Science and Engineering, vol.22, issue.3, pp.528-535, 2002.
DOI : 10.1016/0020-7403(80)90070-3

A. Vyas and M. C. Shawn, The mechanism of chip formation with hard turning steel, Annals of the CIRP, vol.471, pp.77-82, 1998.

G. Poulachon and A. Moisan, A Contribution to the Study of the Cutting Mechanisms During High Speed Machining of Hardened Steel, CIRP Annals, vol.47, issue.1, pp.73-76, 1998.
DOI : 10.1016/S0007-8506(07)62788-7

M. A. Davies, Dynamic problems in hard-turning, milling, and grinding, Dynamics and Chaos in Manufacturing Processes, pp.57-91, 1998.

M. A. Davies, Y. Chou, and C. J. Evans, On Chip Morphology, Tool Wear and Cutting Mechanics in Finish Hard Turning, CIRP Annals, vol.45, issue.1, pp.77-82, 1996.
DOI : 10.1016/S0007-8506(07)63020-0

T. J. Burns and M. A. Davies, On repeated adiabatic shear band formation during high-speed machining1, International Journal of Plasticity, vol.18, issue.4, pp.487-506, 2002.
DOI : 10.1016/S0749-6419(01)00006-7

G. Poulachon, A. Moisan, and I. S. Jawahir, On modelling the influence of thermomechanical behavior in chip formation during hard turning of 100Cr6 bearing steel, Annals of the CIRP, vol.501, pp.31-36, 2001.

S. Dolinsek, S. Ekinovic, and J. Kopac, A contribution to the understanding of chip formation mechanism in high-speed cutting of hardened steel, Journal of Materials Processing Technology, vol.157, issue.158, pp.485-490, 2004.
DOI : 10.1016/j.jmatprotec.2004.07.144

A. Vyas and M. C. Shawn, Mechanics of sawtooth chip formation in metal cutting, Transactions of the ASME Journal of Manufacturing Science and Engineering, vol.121, pp.173-180, 1999.

F. C. Moon and M. Johnson, A, Nonlinear dynamics and chaos in manufacturing processes, Dynamics and Chaos in Manufacturing Processes, pp.3-32, 1998.

C. J. Hooke and S. A. Tobias, Finite amplitude instability ? A new type of chatter, Proc. Fourth Int. MTDR Conf, pp.87-109, 1963.

J. Tlusty and M. Polacek, The Stability of Machine Tools Against Self Excited vibrations in Machining, International Research in Production Engineering ASME, pp.465-474, 1963.

H. E. Merrit, Theory of Self-Excited Machine-Tool Chatter: Contribution to Machine-Tool Chatter Research???1, Journal of Engineering for Industry, vol.87, issue.4, pp.447-454, 1965.
DOI : 10.1115/1.3670861

S. G. Tewani, K. E. Rouch, and B. L. Walcott, A study of cutting process stability of a boring bar with active dynamic absorber, International Journal of Machine Tools and Manufacture, vol.35, issue.1, pp.91-108, 1995.
DOI : 10.1016/0890-6955(95)80009-3

E. P. Nosyvera and A. Molinari, Nonlinear analysis of chatter in orthogonal cutting, C. R

I. Minis and B. S. Berger, Modeling, Analysis, and Characterization of machining Dynamics, Dynamics and Chaos in Manufacturing Processes, pp.125-164, 1998.

B. C. Rao and Y. C. Shin, A comprehensive dynamic cutting force model for chatter prediction in turning, International Journal of Machine Tools and Manufacture, vol.39, issue.10, pp.1631-1654, 1999.
DOI : 10.1016/S0890-6955(99)00007-3

B. E. Clancy and Y. C. Shin, A comprehensive chatter prediction model for face turning operation including tool wear effect, International Journal of Machine Tools and Manufacture, vol.42, issue.9, pp.1035-1044, 2002.
DOI : 10.1016/S0890-6955(02)00036-6

A. Moufki, A. Devillez, M. Segreti, and D. Dudzinski, A semi-analytical model of nonlinear vibrations in orthogonal cutting and experimental validation, International Journal of Machine Tools & Manufacture, vol.46, pp.1-14, 2005.

J. Lee and D. Kim, Experimental modal analysis and vibration monitoring of cutting tool support structure, International Journal of Mechanical Sciences, vol.37, issue.11, pp.1133-1146, 1995.
DOI : 10.1016/0020-7403(95)00029-W

P. O. Sturesson, L. Hakansson, and I. Claesson, IDENTIFICATION OF STATISTICAL PROPERTIES OF CUTTING TOOL VIBRATIONS IN A CONTINUOUS TURNING OPERATION???CORRELATION TO STRUCTURAL PROPERTIES, Mechanical Systems and Signal Processing, vol.11, issue.3, pp.459-489, 1997.
DOI : 10.1006/mssp.1996.9998

K. Kelly, P. Young, and G. Byrne, Modelling the influence of machining dynamics on surface topography in turning, International Journal of Mechanical Sciences, vol.41, issue.4-5, pp.507-526, 1998.
DOI : 10.1016/S0020-7403(98)00079-4

D. E. Dilma and P. M. Lister, On-line metal cutting tool condition monitoring. I: force and vibration analyses, International Journal of Machine Tools & Manufacture, vol.40, pp.739-768, 2000.

T. Mabrouki and J. , A contribution to a qualitative understanding of thermomechanical effects during chip formation in hard turning, Journal of Materials Processing Technology
URL : https://hal.archives-ouvertes.fr/hal-00938632

N. H. Cook, Chip formation in machining titanium Ordnance Corps, Proc. Symp. on Machining and Grinding Titanium, 1953.

M. E. Merchant, Mechanics of the Metal Cutting Process. II. Plasticity Conditions in Orthogonal Cutting, Journal of Applied Physics, vol.27, issue.6, pp.318-324, 1945.
DOI : 10.1103/PhysRev.48.825